Struct bonsaidb::keystorage::s3::aws_sdk_s3::operation::put_bucket_website::builders::PutBucketWebsiteFluentBuilder

pub struct PutBucketWebsiteFluentBuilder { /* private fields */ }

Fluent builder constructing a request to PutBucketWebsite.

Sets the configuration of the website that is specified in the website subresource. To configure a bucket as a website, you can add this subresource on the bucket with website configuration information such as the file name of the index document and any redirect rules. For more information, see Hosting Websites on Amazon S3.

This PUT action requires the S3:PutBucketWebsite permission. By default, only the bucket owner can configure the website attached to a bucket; however, bucket owners can allow other users to set the website configuration by writing a bucket policy that grants them the S3:PutBucketWebsite permission.

To redirect all website requests sent to the bucket's website endpoint, you add a website configuration with the following elements. Because all requests are sent to another website, you don't need to provide index document name for the bucket.

• WebsiteConfiguration

• RedirectAllRequestsTo

• HostName

• Protocol

If you want granular control over redirects, you can use the following elements to add routing rules that describe conditions for redirecting requests and information about the redirect destination. In this case, the website configuration must provide an index document for the bucket, because some requests might not be redirected.

• WebsiteConfiguration

• IndexDocument

• Suffix

• ErrorDocument

• Key

• RoutingRules

• RoutingRule

• Condition

• HttpErrorCodeReturnedEquals

• KeyPrefixEquals

• Redirect

• Protocol

• HostName

• ReplaceKeyPrefixWith

• ReplaceKeyWith

• HttpRedirectCode

Amazon S3 has a limitation of 50 routing rules per website configuration. If you require more than 50 routing rules, you can use object redirect. For more information, see Configuring an Object Redirect in the Amazon S3 User Guide.

The maximum request length is limited to 128 KB.

Implementations

impl PutBucketWebsiteFluentBuilder

pub fn as_input(&self) -> &PutBucketWebsiteInputBuilder

Access the PutBucketWebsite as a reference.

pub async fn send( self ) -> impl Future<Output = Result<PutBucketWebsiteOutput, SdkError<PutBucketWebsiteError, Response<SdkBody>>>>

Sends the request and returns the response.

If an error occurs, an SdkError will be returned with additional details that can be matched against.

By default, any retryable failures will be retried twice. Retry behavior is configurable with the RetryConfig, which can be set when configuring the client.

pub async fn customize( self ) -> impl Future<Output = Result<CustomizableOperation<PutBucketWebsiteOutput, PutBucketWebsiteError, PutBucketWebsiteFluentBuilder>, SdkError<PutBucketWebsiteError, Response>>>

Consumes this builder, creating a customizable operation that can be modified before being sent.

pub fn bucket(self, input: impl Into<String>) -> PutBucketWebsiteFluentBuilder

The bucket name.

pub fn set_bucket(self, input: Option<String>) -> PutBucketWebsiteFluentBuilder

The bucket name.

pub fn get_bucket(&self) -> &Option<String>

The bucket name.

pub fn content_md5( self, input: impl Into<String> ) -> PutBucketWebsiteFluentBuilder

The base64-encoded 128-bit MD5 digest of the data. You must use this header as a message integrity check to verify that the request body was not corrupted in transit. For more information, see RFC 1864.

For requests made using the Amazon Web Services Command Line Interface (CLI) or Amazon Web Services SDKs, this field is calculated automatically.

pub fn set_content_md5( self, input: Option<String> ) -> PutBucketWebsiteFluentBuilder

The base64-encoded 128-bit MD5 digest of the data. You must use this header as a message integrity check to verify that the request body was not corrupted in transit. For more information, see RFC 1864.

For requests made using the Amazon Web Services Command Line Interface (CLI) or Amazon Web Services SDKs, this field is calculated automatically.

pub fn get_content_md5(&self) -> &Option<String>

The base64-encoded 128-bit MD5 digest of the data. You must use this header as a message integrity check to verify that the request body was not corrupted in transit. For more information, see RFC 1864.

For requests made using the Amazon Web Services Command Line Interface (CLI) or Amazon Web Services SDKs, this field is calculated automatically.

pub fn checksum_algorithm( self, input: ChecksumAlgorithm ) -> PutBucketWebsiteFluentBuilder

Indicates the algorithm used to create the checksum for the object when using the SDK. This header will not provide any additional functionality if not using the SDK. When sending this header, there must be a corresponding x-amz-checksum or x-amz-trailer header sent. Otherwise, Amazon S3 fails the request with the HTTP status code 400 Bad Request. For more information, see Checking object integrity in the Amazon S3 User Guide.

If you provide an individual checksum, Amazon S3 ignores any provided ChecksumAlgorithm parameter.

pub fn set_checksum_algorithm( self, input: Option<ChecksumAlgorithm> ) -> PutBucketWebsiteFluentBuilder

Indicates the algorithm used to create the checksum for the object when using the SDK. This header will not provide any additional functionality if not using the SDK. When sending this header, there must be a corresponding x-amz-checksum or x-amz-trailer header sent. Otherwise, Amazon S3 fails the request with the HTTP status code 400 Bad Request. For more information, see Checking object integrity in the Amazon S3 User Guide.

If you provide an individual checksum, Amazon S3 ignores any provided ChecksumAlgorithm parameter.

pub fn get_checksum_algorithm(&self) -> &Option<ChecksumAlgorithm>

Indicates the algorithm used to create the checksum for the object when using the SDK. This header will not provide any additional functionality if not using the SDK. When sending this header, there must be a corresponding x-amz-checksum or x-amz-trailer header sent. Otherwise, Amazon S3 fails the request with the HTTP status code 400 Bad Request. For more information, see Checking object integrity in the Amazon S3 User Guide.

If you provide an individual checksum, Amazon S3 ignores any provided ChecksumAlgorithm parameter.

pub fn website_configuration( self, input: WebsiteConfiguration ) -> PutBucketWebsiteFluentBuilder

Container for the request.

pub fn set_website_configuration( self, input: Option<WebsiteConfiguration> ) -> PutBucketWebsiteFluentBuilder

Container for the request.

pub fn get_website_configuration(&self) -> &Option<WebsiteConfiguration>

Container for the request.

pub fn expected_bucket_owner( self, input: impl Into<String> ) -> PutBucketWebsiteFluentBuilder

The account ID of the expected bucket owner. If the bucket is owned by a different account, the request fails with the HTTP status code 403 Forbidden (access denied).

pub fn set_expected_bucket_owner( self, input: Option<String> ) -> PutBucketWebsiteFluentBuilder

The account ID of the expected bucket owner. If the bucket is owned by a different account, the request fails with the HTTP status code 403 Forbidden (access denied).

pub fn get_expected_bucket_owner(&self) -> &Option<String>

The account ID of the expected bucket owner. If the bucket is owned by a different account, the request fails with the HTTP status code 403 Forbidden (access denied).

Trait Implementations

impl Clone for PutBucketWebsiteFluentBuilder

fn clone(&self) -> PutBucketWebsiteFluentBuilder

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Debug for PutBucketWebsiteFluentBuilder

fn fmt(&self, f: &mut Formatter<'_>) -> Result<(), Error>

Formats the value using the given formatter.